The 1.1 mile extension of Martin Luther King Jr. Boulevard (MLK) from Havana Street east to Peoria Street is a planned transportation improvement within the Stapleton Redevelopment Area. The new roadway will extend mostly through the City and County of Denver, and a small portion will be located within the City of Aurora.
Work on the extension of Martin Luther King Blvd began in November 2018 and is expected to continue until September 2020.
Access to residential neighborhoods will be maintained at all times, although there could be periodic delays when equipment is working in front of entrances. Traffic control will be in place during the hours of 7AM and 5:30PM Monday through Friday, as well as on an on-call basis outside of those hours.
Current street closures include Lima and Ironton. Kingston is open. Traffic is expected to access Iola to Peoria by the end of January 2020.
All work is weather dependent.
The Colorado Department of Transportation (CDOT) and the Federal Highway Administration (FHWA) prepared a National Environmental Policy Act (NEPA) Environmental Assessment (EA) in 2011. At that time, a Finding of No Significant Impact (FONSI) was not made by the CDOT and FHWA because funding was not available to construct the project. Since then, a combination of federal and local funding has been identified and the project is able to move forward.
The City and County of Denver has prepared a NEPA EA Reevaluation of the project that was approved by CDOT and FHWA in June 2017. The NEPA EA Reevaluation updates the environmental analysis to reflect current site conditions as well as new CDOT/FHWA and other environmental requirements.
Following a month-long public review and comment period that included a public meeting, a Finding of No Significant Impact (FONSI) was approved by CDOT and FHWA on October 19, 2017. With this approval, the project is proceeding into final design, permitting and construction.
Finding of No Significant Impact (FONSI) – October 2017 (PDF)
The MLK Extension noise wall voting process is presumed to be completed as of 4:00 pm on 7/21/17; three days past the voting deadline at midnight 7/18/17. This additional time was to allow all mailed ballots to be received by CCD PW. The voting results are
Yes = 15 (27.3%)
No = 40 (72.7%)
71.4 % of possible votes cast
Yes = 5 (12.8%)
No = 34 (87.2%)
75% of possible votes cast
Yes = 9 (47.4%)
No = 10 (52.6%)
63.3% of possible votes cast
Documentation of the voting results will be mailed to all benefited receptors, and will be presented at the public meeting on Tuesday, July 25.
The noise analysis process conducted per requirements of the Colorado Department of Transportation (CDOT) “Noise Analysis and Abatement Guidelines, 2015” determined that noise abatement, in the form of noise walls, is both reasonable and feasible along three separate portions of the project on the south side of the new MLK Blvd. from Ironton St. to Moline St. Along these three blocks, adjacent property owners and residents (benefited receptors) will be asked to vote on their preference for, or against, the construction of a noise wall within their block. If a majority of benefited receptors vote to approve a noise wall within their block, Denver will construct a noise wall. If not, no wall(s) will be constructed. The voting process will conclude in mid-July and results will be posted on this webpage.
A short section of a demonstration noise wall has been constructed just west of Kingston St. along the new MLK alignment. There will be a site meeting and mock wall demonstration on July 5th from 4:30 to 6:30 pm to answer questions that voters may have.
A visual simulation ‘fly-through’ of the walls can be viewed online (one per block) and at the July 5 meeting.
Please note: these Autodesk links require an updated desktop browser with Flash enabled and may not work on mobile devices or older computers. Chrome or Firefox recommended.
The data may take several minutes to load, depending on connection speed. Once the model has loaded, you can interact with the static model, or view an animated for the noise wall by clicking the "movie" icon in the upper left of the page. Select the "story board" for that block to begin the animation. While the animation plays, you can toggle the noise walls on and off to see the perspective with and without the wall using the “Layers” control located next to the Story Board icon. Check the barriers box on/off while the animation is running.